[su_subpages depth=”3″]

• Safety Yellow Line Marking with Concrete Mender™ Yellow.

 

Concrete repair for freezer and cold storage warehouse floors.

If your business is refrigerated warehousing or grocery distribution, Roadware 10 Minute Concrete Mender™ is the premier concrete repair product for keeping your floors in top condition. The unique Microdoweling™ polyurethanes in Concrete Mender™ will cure at temperatures well below -20 degrees F. ( -28 C) in just a few hours. You can repair cracks, spalls, slabs, joints, and surfaces while the warehouse is in service.

Features:

• Easy to mix one-to-one ratio polyurethane.
• Add manufactured sand to extend the material over to two times. Two gallons of Concrete Mender™ will make 4.4 gallons of repair material.
• Ultra low viscosity for easy application and workability.
• Microdoweling™ penetration into the concrete for load transfer bonding.
• Cures only has hard as the concrete. Will not become brittle like epoxy.
• Tough repairs that can take industrial levels of punishment.

Benefits:

• Smooth and safe floors.
• Less damage to forklifts and equipment.
• Clean floors. Meets FSIS and USDA guidelines.
• Less tipped loads and damaged product.
• Reduced cleaning and floor maintenance costs.
• Reduced workers comp claims attributed to accidents.

Cold environments such as walk-in freezers and refrigerated warehousing pose difficult challenges for repairing concrete. In temperatures less than 0° F, most repair materials become unworkable and may take many hours to set and cure. Most epoxies are not usable below 32° F. Roadware Polyurethanes have been used in temperatures as low as -20°F below freezing. Listed below are some problems and solutions for working in cold environments.

Cold Environment Challenges

Frost: Frozen moisture in the concrete will act as a barrier between the repair material and the pours of the concrete. Most repair materials will try to bond to the frost coated concrete. When the temperature increases, the frost melts and so does the bond.

Working Conditions: Working with materials in the cold is challenging to both man and materials. Mixing epoxies or mortars in the cold is especially challenging. As the temperature decreases, the viscosity and flow rate of these materials increase making them harder to mix and much more difficult to work with.

Curing: With most materials, cure times in cold environments are extended significantly. A product that normally cures in an hour at room temperature may take as much as 12 hours in a cold environment. Some materials may not cure at all before actually freezing solid.

ROADWARE Solutions

 

The extremely low viscosity and rapid cure times of Roadware 10 Minute Concrete Repair products make them excellent for cold environment application. Successful repairs are routinely made at temperatures below -20°F in freezer floors.

Preparation: Prepare cracks, joints, and spalls according to standard recommended methods. Make every effort to remove any moisture from the repair area. A propane torch or heat gun is very helpful in removing frost and moisture. In extreme cold, it is necessary to heat up the concrete prior to application.

Application: Keep material and sand or aggregate warm. Place materials in a warm area (between 70°F and 90°F) prior to application. Warm cartridges mix better, flow easier, and cure faster. Apply material as directed. It is a good practice to pre-wet all concrete surfaces with material before the introduction of sand. This insures full penetration and a strong bond.

Curing: Roadware materials are designed to cure in approximately 10 minutes when all components involved are at 70° F. In cold environment, the cure time depends on the temperature of the material, the temperature of the sand or aggregate if used, the volume of the repair, and the temperature of the concrete. Below is a chart of approximate cure times at various temperatures and conditions.

 

 

Real Life Examples

Freezer Threshold Repairs

 

Roadware 10 Minute Concrete Mender™ saves food distribution warehouse thousands of dollars for over 15 years.

 

COVERAGE CHART

ROADWARE 10 MINUTE CONCRETE MENDER™

Approximate yield with 40-30 silica sand mixed 2 parts sand to 1 part liquid.

SIDE A	SIDE B	SAND	MIXED MATERIAL	CUBIC INCHES
4 OZ	4 OZ	16 OZ	17.5 OZ	32
8 OZ	8 OZ	32 OZ	35 OZ	64
16 OZ	16 OZ	64 OZ	70 OZ	128
1/2 GAL	1/2 GAL	2 GAL	2.2 GAL	508
GAL 1	1 GAL	4 GAL	4.4 GAL	1016

ORDERING INFORMATION

ROADWARE 10 MINUTE CONCRETE MENDER™

Item Number	Kit
80300	300x300ml twin cartridge
80020	2 gallon kit in one gallon cans
80040	4 gallon kit in one gallon cans
80050	10 gallon kit in 5 gallon cans

 

 

Roadware MatchCrete™ Concrete Mender in safety yellow color is used for permanent line marking in cold storage and freezer floors.